Electrim 30L MaxiBAB "Heart of Gold IPA" [Pic Heavy]

Post #1 made 12 years ago
Well I had planed to document my last brew as another member was asking about using an Eectrim Boiler for BIAB I but didn't have my camera with me. So today (well starting off last night) I brewed a single hop IPA which I am calling "Heart of gold" (the recipe is untested so I'll report back if its any good)

I use Brewtarget software and here is the recipe
I do an overnight mash so I started at 1am last night (or this morning if you prefer).
Grain weighed out and ready to go
Image
Water is on Campden Tablet is in 75:25 RO:Tap water waiting for strike temperature before doughing in.
Tucked up for the night
Image
Starting temperature
Image
End temperature after about 9 hours
Image
Unpacking
Image
Looks good :)
Image
The "sparge" basically soaking the grain sack for 10 minutes during which the wort below is starting to heat up.
Image
75% of the sparge water has been put in and the hops go in the hop sock with the temperature at about 85C so not quite boiling yet, the rest of the sparge water will go in with about 40 minutes left as evaporation will have made space by then.
Image
The hot break I think? One advantage of a hop sock is that the bag catches a lot of the break material.
Image
A nice rolling boil time to sit for a bit.
Image
The Golden syrup was added 10 minutes before flame out (mixed with 1L of boiling wort) then at flame out 2L of tap water was added in to top up the wort was then and chilled and transferred to the FV
Image

2L of top up give give me an OG of 1.052 so about 5% ABV is expected and an the efficiency comes out around the 86% mark
Image
The yeast was pitched and its now sat at the back of my kitchen.
Last edited by Jeltz on 07 Feb 2013, 00:17, edited 2 times in total.
Regards

Nic

Post #2 made 12 years ago
Looks like you had a good brewday/night there, and the electrim worked as you wanted.All systems go!! Well done and thanks for the pics.
If you can gauge it properly,I might suggest that you add your top up water a little earlier to give it a little boil time with the wort.
AWOL

Post #3 made 12 years ago
If I could I would but with the displacement from the hops it just takes it over the height where I get splash out, by adding it before the chilling I reckon that any nasties are killed as the temperature was still above 90C for several minutes. As I understand it from cooking very little survives above 70C.
Regards

Nic

Post #5 made 12 years ago
Shhhh don't tell anyone but on the last three brews I just added it straight from the tap to the fermenter without problem.

I considered boiling some water beforehand to use for to but chose not to for the following reasons
  • Its mixing with very hot wort.
  • There is chlorine in the water (I don't bother with campden for the top up) which is intended to keep it sterile.
  • Boiling would drive off the chlorine so if it were allowed to cool may leave it more open to being infected.
  • Its just one more thing to do/remember an already busy day (probably the most significant reason)
Last edited by Jeltz on 07 Feb 2013, 02:59, edited 3 times in total.
Regards

Nic

Post #6 made 12 years ago
Jeltz, I was caught in a fight er... discussion on here recently about tap water, and even using hot tap water for added assurance that it might be sterile. I was pro tap water. It's sterile in most places. Others were opposed.

I won’t say anything to anyone!

It’s interesting to hear you haven’t had problems with the few batches, and I like the way you reason things out.

Cover up your chips for a little while though :)
Guinges
Post Reply

Return to “Electric BIAB”

Brewers Online

Brewers browsing this forum: No members and 13 guests

cron