Hi guys,
I couldn't find the answer to my question.
What's the best way to transfer the boil to the cube? Is it safe to use the tap in my Pot? Should I use a hose in it? Or let the boil drop directly to the cube?
Thanks
Post #2 made 11 years ago
I use a silicone hose attached to my valve. It is safe and avoids a lot of splashing which you don't want at this point. Just be very careful of the sanitation of the valve or PP will be all over both of us.
AWOL
Post #3 made 11 years ago
Tsar,,
As lylo indicated above. You should avoid "Hot side aeration". Look at the second last picture at the link below. http://www.stempski.com/biab.php I did this a few years ago but it is still relevant.
here is a link to the tubing I use. They have different sizes and it's cheap. Not clear tubing!
http://www.northernbrewer.com/shop/3-8- ... ing-1.html
http://home-brewing.northernbrewer.com/ ... emp+tubing
Cheers
As lylo indicated above. You should avoid "Hot side aeration". Look at the second last picture at the link below. http://www.stempski.com/biab.php I did this a few years ago but it is still relevant.
here is a link to the tubing I use. They have different sizes and it's cheap. Not clear tubing!
http://www.northernbrewer.com/shop/3-8- ... ing-1.html
http://home-brewing.northernbrewer.com/ ... emp+tubing
Cheers
Last edited by BobBrews on 05 Mar 2013, 04:11, edited 2 times in total.
tap 1 Raspberry wine
tap 2 Bourbon Barrel Porter
tap 3 Czech Pilsner
tap 4 Triple IPA 11% ABV
Pipeline: Mulled Cider 10% ABV
http://cheesestradamus.com/ Brewers challenge!
tap 2 Bourbon Barrel Porter
tap 3 Czech Pilsner
tap 4 Triple IPA 11% ABV
Pipeline: Mulled Cider 10% ABV
http://cheesestradamus.com/ Brewers challenge!
-
- SVA Brewer With Over 100 Brews From United States of America
-
Post #4 made 11 years ago
Use your tap, but don't let PP know about it.
EDIT: Seriously though, a tap or valve can get gunked up, unless you have a 3-piece that you can break down for cleaning.
EDIT: Seriously though, a tap or valve can get gunked up, unless you have a 3-piece that you can break down for cleaning.
-
- SVA Brewer With Over 100 Brews From United States of America
-
Post #5 made 11 years ago
Use a length of silicone hose attached to a stainless racking cane.
Easy, simple and no chance of HSA.
Easy, simple and no chance of HSA.
"It's beer Jim, but not as we know it."
Post #6 made 11 years ago
Hashie, how do you start a syphon (with your mouth?) and have you ever tied some voile around your silicone hose to strain?hashie wrote:Use a length of silicone hose attached to a stainless racking cane.
Easy, simple and no chance of HSA.
I bumped Yeasty's thread; http://biabrewer.info/viewtopic.php?f=53&t=1108#p14731" onclick="window.open(this.href);return false; , he is using it to syphon / strain when it is chilled, BUT can't you use it to syphon when hot also? Can't you also cover the manifold with a voile bag and strain it from pellet hops?, like pictured here. I had no need to vorlauf when I used my copper manifold in my MLT.
12/11/2010 by Mad Scientist Brewhaus, on Flickr
Last edited by Mad_Scientist on 06 Mar 2013, 06:25, edited 2 times in total.
-
- SVA Brewer With Over 100 Brews From United States of America
-
Post #7 made 11 years ago
Is it safe to use silicone hose in boil temperature?
'Cause if it is, if we dip all the hose in the liquid, the hose will be full, then we close the hose and put it in the cube, and then open it, and the siphon will begin, I think...
Hope you understand my bad english
'Cause if it is, if we dip all the hose in the liquid, the hose will be full, then we close the hose and put it in the cube, and then open it, and the siphon will begin, I think...
Hope you understand my bad english
-
- Over 5 Brews From Portugal
-
Post #8 made 11 years ago
Yeah tsar that work. I have used the methocd before,but I highly recommend that you give it a practise run first,with cold water and the actual vessels you will be using.
As BobBrew is fond of saying"don't ask how I know"
As BobBrew is fond of saying"don't ask how I know"
AWOL
Post #10 made 11 years ago
Start the siphon with my mouth yes. I know people say how dangerous that is etc. but silicone hose is somewhat see through, it is certainly not opaque. I can see the liquid as it rises up the tube, yes rises, I wouldn't do it where my face was lower than the top of the kettle for obvious safety reasons. Once the hose is all but full, I quickly put it into the cube and let the siphon happen.Mad_Scientist wrote:Hashie, how do you start a siphon (with your mouth?) and have you ever tied some voile around your silicone hose to strain?hashie wrote:Use a length of silicone hose attached to a stainless racking cane.
Easy, simple and no chance of HSA.
I haven't tried putting voile as a strainer, I just allow whatever is picked up to go into the cube where it will settle out.
Last edited by hashie on 07 Mar 2013, 08:44, edited 2 times in total.
"It's beer Jim, but not as we know it."
Post #11 made 11 years ago
I use it when hot and filling a cube as well. I start the syphon with a spare piece of tubing attached to a small inline tap, which I pull off once the wort is up and over the pot lip. I then fill a 2L jug a few times and recirculate, I then add another piece of tube that reaches the bottom of the cube and fill as normal.Mad_Scientist wrote:I bumped Yeasty's thread; viewtopic.php?f=53&t=1108#p14731 , he is using it to syphon / strain when it is chilled, BUT can't you use it to syphon when hot also? Can't you also cover the manifold with a voile bag and strain it from pellet hops?, like pictured here. I had no need to vorlauf when I used my copper manifold in my MLT
Last edited by Yeasty on 08 Mar 2013, 06:13, edited 2 times in total.
Why is everyone talking about "Cheese"
-
- SVA Brewer With Over 50 Brews From Great Britain
-
Post #12 made 11 years ago
I have posted this link before and I know that it works well,even if it is a Canucks idea.
http://www.homebrewtalk.com/f11/flyguys ... hon-25774/
http://www.homebrewtalk.com/f11/flyguys ... hon-25774/
AWOL
Post #13 made 10 years ago
I use a 1m length of silicone hose attached to the ball valve on my keggle to transfer to the cube. The valve itself is capable of being fully disassembled and is cleaned thoroughly after every brew day